+1-877-452-0010×1 | M-F 8am-8pm US EST



Fusion3’s mission is to engineer 3D printers that can build large, strong parts from high-strength / high-temperature materials. ABS, being one of the most popular material in this category provides the best test of our 3D printers, and customers find that every Fusion3 3D printer is ideally suited to print large parts from ABS and produce great results.

ABS (acrylonitrile-butadiene-styrene) is fantastic thermoplastic for 3D printing and demonstrates very good engineering-grade characteristics. You’ll find ABS to be strong, providing impact, heat and abrasion resistance. ABS is somewhat chemical resistant. Its surface is hard, the material pretty rigid and provides good tensile strength and dimensional stability. ABS in filament form, compared to other thermoplastics, is quite inexpensive and can be purchased from high quality suppliers from $20.00 to $30.00 USD per Kilogram.

ABS is one of many 3D printing materials that fall in the category of high-temperature materials (requiring printing at temperatures hotter than room temperature) which pose special challenges for consumer/low-cost 3D printers. As a result, from a consumer or hobbyist perspective, certain materials like ABS have an undeserved reputation as not well suited for 3D printing.

ABS 3D Printed Welding Clamp


Rotor Shaft 3D printed with generic ABS

There are hundreds of ABS 3D printer filaments on the market, many from overseas/low-cost markets. However it is worth spending a few more dollars per kilogram for filament from a high-quality domestic supplier who focuses on precision and consistency of extrusion.

Over 27 Different Generic & Speciality ABS 3D Printer Filaments, Tested & Certified For Fusion3 3D Printers

We have tested and certified a wide variety of ABS materials from leading manufacturers for use in our 3D printers.

Fusion3 receives requests from both customers and manufacturers to test new materials as they arrive on the market. Should they pass our rigorous testing process, we provide optimized print settings to all our customers within our F3Slic3r 3D printing software.

The New EDGE High-Performance 3D Printer

Optimized For 3D Printing Higher-Temperature Materials Including ABS



Enclosed, Passively Heated Print Chamber For Optimal Results

ABS Parts Must Stay Warm For Proper Layer Adhesion

Every Fusion3 3D printer’s enclosure does two important things to ensure great layer adhesion for your 3D printed ABS parts. First, the enclosure passively retains heat given off by the heated print bed and the print head, raising the ambient temperature of the build chamber and further reducing thermal stress. Second, The enclosure eliminates the influence of air drafts, like downdrafts from air conditioning which could rapidly cool the part.

Infrared Image of the Fusion3 EDGE’s Multizone Heated Bed

Precision Print Heads For High-Temperature, High-Flow 3D Printing

Successful ABS 3D Prints Require Your Print Head To Melt Quickly And Keep Up

Fusion3’s focus on speed and print quality has required us to use high-flow, high temperature print heads that allow for quick heating of material and sustained, high temperatures to maintain a high rate of material flow. Our Fusion3 EDGE maintains this tradition, using our new ANVIL print head. With its surgical steel print tubes, and higher performance PT1000 temperature sensor and heater cartridges, EDGE is able to heat quickly and maintain the fastest flow rates of any 3D printer Fusion3 has ever built, maintaining consistent high heat, ensuring rapid extrusion and strong bonds between the layers.

Fusion3’s Precision ANVIL Print Head

High Power, Multi-Zone Bed Heaters

ABS Parts Require a Hot Print Bed To Avoid Warping

Fusion3’s 3D printers have always used high-power, multi-zone print beds. This technology breaks the print surface into multiple, discrete zones with different power densities, keeping the entire Fusion3 3D printer’s surface at the same temperature. This helps prevent undesirable cooling of the 3D printed ABS part and warp for properly designed parts.

Infrared Image of the Fusion3 EDGE’s Multizone Heated Bed

Interested In Seeing Your File Printed In ABS On The New Fusion3 EDGE 3D Printer?